Software Overview

Below you find an overview of EMC PARTNER's remote control software for Windows. You can download a full installation or an update to your actual version by clicking the link after the short description of the software.

All softwares have a demo-mode where the generators are simulated.

For detailed information please do not hesitate to contact our representative in your region.


TEMA 1.81

TEMA is a Windows based software for the Transient-2000
and MIG testers (2000er series)  > see under Products

It includes:
  • remote control
  • complex test sequences (click for examples in the area of component testing)
  • extended protocolling (HTML or Winword export)
  • EUT supervision with oscilloscope

Click for the computer requirements of this software.

The software has a demo-mode where the generators are simulated. To run TEMA with your generator you have to purchase an "entry-code" for each generator.




GENECS 2.77

GENECS is a simple Windows based remote control software for the Transient-2000 and MIG testers (2000er series) > see under Product.

It includes:

  • remote control
  • protocolling

Click for the computer requirements of this software.

You will find more information about GENECS in the according brochure (PDF).

The software has a demo-mode where the generators are simulated. For the Transient-2000 the software is free and runs without any "entry-code".
GENECS is also part of the TEMA software and runs for MIG testers with the same "entry-code".




HARCS 4.16  (Firmware Version 2.18)

HARCS is the Windows based software for the Harmonics-1000
> see under Products.

It includes:

  • emission measurement and ANASIM
  • immunity (optional)

New in HARCS 4.xx:

  • full 32-bit version (for Windows 95/98, NT, 2000, XP)
  • expanded test report generator with more test information and export to HTML-format
  • flicker:
    • including Amendment 1 with flickermeter for 120 V / 60 Hz
    • enhanced flicker simulator (ANASIM)
  • harmonics emission:
    • more transparency (You find all details about limit calculations and measuring methods and definitions in the protocol printout.)
    • including interharmonics
  • harmonics immunity:
    • update to published 61000-4-13 Ed.1
  • including IEC 61000-4-7 Ed. 2: 2002 (e.g. 200 ms Rectangular DFT Window)

Click for the computer requirements of this software.

For more information about HARCS see the support link, the new examples and the application notes in the HARCS software.

The HARCS installation includes also the firmware for the Harmonics-1000. This firmware has to be downloaded to the Harmonics-1000 after installation.




E3loader 3.30

E3loader is the Windows based software for the ESD3000 ESD simulator.

It includes:

  • up- and download of parameter setups
  • firmware update
  • upload of calibration factors
  • maintenance

Click for the computer requirements of this software.

The E3loader  installation includes also the firmware for the ESD3000. This firmware has to be downloaded to the ESD3000 after installation.



PS3SOFT-EXT 1.24

PS3SOFT-EXT is the Windows based software for the power supply PS3.

It includes:

  • programming of test setups for frequency variation (IEC61000-4-28) and voltage variation
  • remote control of the power supply PS3

Click for the computer requirements of this software.



Test Procedure Database 1.00

The Test Procedure Database is a collection of standard procedure for EMC and component testing. It is the same database as you find online on the web. This link below leads to a downloadable version which will install the database on your local computer in the TEMA directory.

To run the procedures you need an installed TEMA software with a valid "entry-code" for your generator.



TRACS 3.9 (not for demo use)

TRACS is the Windows based software for Transient-1000. The software is no longer supported but still available for download. There is no demo version available. See computer requirements for the limitations.

It includes:

  • remote control
  • protocolling
  • EMC library

TRACS plus :

  • EUT supervision with oscilloscope
  • extended protocolling

Click for the computer requirements of this software.

You will find more information about TRACS in the according brochure (PDF).




MIGCS 3.7 (not for demo use)

MIGCS is the Windows based software for MIG testers (Series 1000). The software is no longer supported but still available for download. There is no demo version available. See computer requirements for the limitations.

It includes:

  • remote control
  • protocolling
  • EUT supervision with oscilloscope

Click for the computer requirements of this software.